Early Javelin Restoration

[Grumpy Northener]

Not posted for a couple of weeks as I was a main player in the staging of our annual Jowett international rally in Basingstoke (pics to follow soon) so what's been happening in the meantime ?

WP_20130518_002-001.jpg (72.59 KiB) Viewed 1642 times

Well I managed to locate a scrap trolley out of a skip which provided wheels & stub axles for a body shell trolley so I set about fabricating a couple of axles - front one will be steering

WP_20130518_003-001.jpg (63.35 KiB) Viewed 1642 times

[Grumpy Northener]

WP_20130518_006-001.jpg (65.8 KiB) Viewed 1642 times

WP_20130518_005-001.jpg (71.48 KiB) Viewed 1642 times

WP_20130518_010-001.jpg (77.37 KiB) Viewed 1642 times

This now gives the ability to move the shell around the workshop once all the welding is complete and the body shell comes off the chassis tilter

[Grumpy Northener]

WP_20130523_003-001.jpg (92.21 KiB) Viewed 1642 times

It also means that the project can attend our national rally

WP_20130525_012-001.jpg (66.71 KiB) Viewed 1642 times

WP_20130525_016-001.jpg (63.92 KiB) Viewed 1642 times

Where it provided the topic of many conversations with Javelin owners / restorers alike

[Grumpy Northener]

WP_20130528_001-001.jpg (73.59 KiB) Viewed 1621 times

The rear shocker mountings were all but hanging off - this is the nearside one

WP_20130528_004-001.jpg (69.25 KiB) Viewed 1621 times

Mounting removed completely along with a poor repair to the rear seat upstand which was cut out and refabricated

[Grumpy Northener]

WP_20130528_005-001.jpg (71.63 KiB) Viewed 1620 times

I managed to clean the old mounting up and once I had fabricated a new back plate the mounting was rewelded into place along with new strengthening webs

WP_20130528_007-001.jpg (68.27 KiB) Viewed 1620 times

And here is the latest addition to the workshop organisation department - a new tool trolley - well used but cost nothing (it's actually a supermarket dairy trolley) keeps everything to hand and saves having to rack it all on shelves at the other end of the workshop.

[Topaz]

And here is the latest addition to the workshop organisation department - a new tool trolley - well used but cost nothing (it's actually a supermarket dairy trolley) keeps everything to hand and saves having to rack it all on shelves at the other end of the workshop.

Ha! I like that idea - my son works at Tesco and drives a 1979 Mini - I'll have to see if he can tow one home for me as it won't fit in the boot

We already have the base of one of their large 'cages' used for stock delivery - a lorry crushed most of the superstructure and so we rescued the base and castors - very handy for resting his Mini engine on and moving it around the garage.

Mike

[Grumpy Northener]

A suspect area was noticed adjacent to the shocker mounting point - this is a double skinned panel and sure enough when tapped with the hammer - through it went

WP_20130601_009-001.jpg (76.08 KiB) Viewed 1608 times

WP_20130601_010-001.jpg (76.61 KiB) Viewed 1608 times

Carefully cut back to sound metal with the air saw

WP_20130601_011-001.jpg (80.01 KiB) Viewed 1608 times

Inner side complete

[Grumpy Northener]

WP_20130601_014-001.jpg (57.07 KiB) Viewed 1608 times

Outer skin prepped for welding in

WP_20130601_015-001.jpg (55.51 KiB) Viewed 1608 times

Cleaned back

[Grumpy Northener]

Next on the list was to sort the O/S/R inner wing section around the shroud area to which the rear outer wing is bolted

WP_20130601_012-001.jpg (53.24 KiB) Viewed 1608 times

Not has bad as the nearside

WP_20130601_013-001.jpg (56.92 KiB) Viewed 1608 times

Another one off the list

[Grumpy Northener]

I rotated the car on the tilter to access the offside shocker mounting

WP_20130601_017-001.jpg (75.86 KiB) Viewed 1608 times

Again all but hanging off - look carefully and you can see cracks in the welds all around the mounting areas

WP_20130601_018-001.jpg (76.52 KiB) Viewed 1608 times

Mounting removed

WP_20130601_019-001.jpg (72.64 KiB) Viewed 1608 times

No end of bodged welding attached to the mounting