MGB GT 2.8 V6

[crabo249]

I have always liked the MGB GT so in 2010 i took the plunge and bought a 1978 model off Ebay

This is how the car looked when i picked her up

MGB1.jpg (30.97 KiB) Viewed 5055 times

Outside the carwash for a wash and brushup as the car had been standing for 9 months

MGB13.jpg (17.26 KiB) Viewed 5001 times

Full of enthusiasm the stripdown begins

MGB3.jpg (63.45 KiB) Viewed 5055 times

also discovered lots of melted wires and a fair bit of rust

[crabo249]

Off to the welders for a marathon session

MGB5.JPG (65.88 KiB) Viewed 5033 times

Cut out all rusty metal and welded in some new tin

New sills and castle rails welded on with wing trumpets,rubber bumper mounts have been cut off to convert to chrome bumpers

New rear wings wheel arches and chrome bumper valance added

MGB6.JPG (63.08 KiB) Viewed 5033 times

[crabo249]

With the welding finished its time to start putting the car back together

MGB83.JPG (46.31 KiB) Viewed 5000 times

I've lead loaded all the welds to try and use as little filler as possible

MGB93.JPG (50.53 KiB) Viewed 5000 times

[crabo249]

The front crossmember,antiroll bar,and suspension parts have been sandblasted & powder coated
All new polybushes,replaced wheel bearings added drilled and grooved disks new calipers and brake hoses
Chrome bumper height springs were used , the shock absorbers are refurbished units from Moss UK as the originals were in a very poor condition

Front cross member

SAM_0023.JPG (78.58 KiB) Viewed 4996 times

The rear axle has had the same sndblast and powdercoating as the front and new leaf springs have been attached

Back axle

SAM_0027.JPG (58.63 KiB) Viewed 4996 times

A chrome bumper valance has been added and the back axle attached to the car
Adjustable shocks have replaced the old lever arm ones
The underneath of the car has had a couple of coats of Schutz to keep the tin worm at bay

Rear valance

SAM_0029.JPG (85.95 KiB) Viewed 4996 times

[crabo249]

Added the front crossmember to car so i now have a rolling chassis

Front suspension looking all nice and shiny

SAM_0034.JPG (82.63 KiB) Viewed 4988 times

Petrol tank has bee cleaned and powder coated

SAM_0066.JPG (75.63 KiB) Viewed 4988 times

MGb on four wheels at last

SAM_0039.JPG (75.54 KiB) Viewed 4988 times

[crabo249]

Brake lines have been fitted so the car can stop when i push it around the unit

Brake lines fitted

SAM_0050.JPG (78.67 KiB) Viewed 4986 times

The panel gaps on the doors needs a bit of work so that'll keep me busy for a while

n/s door

SAM_0071.JPG (62.29 KiB) Viewed 4986 times

o/s door

SAM_0073.JPG (57.33 KiB) Viewed 4986 times

I have been lucky egnough to store my car in a local garage unit so if i do have any problems there is always somebody there to ask

[crabo249]

Took the car back home to my garage to have a go at spraying
Covered everything with plastic sheets waited for a warm day and had a go

Hanging up ready for paint

SAM_0106.JPG (75.29 KiB) Viewed 4985 times

Took of the wings doors and tailgate to spray seperately

SAM_0124.JPG (77.38 KiB) Viewed 4985 times

Not bad for a first attempt

SAM_0127.JPG (74.73 KiB) Viewed 4985 times

[crabo249]

With the car now in undercoat to keep the rust at bay it was time to refit the engine
A scrap sierra came my way with a lovely 2.8 v6 cologne engine i wonder if it will fit

Colopgne 2.8 v6

Rebuild January 016.JPG (62.17 KiB) Viewed 4982 times

fits like a glove

The o/s exhaust manifold was to close for comfort and the n/s hit the chassis rails

O/S Manifold

Rebuild January 020.JPG (57.86 KiB) Viewed 4982 times

n/s manifold

Rebuild January 021.JPG (59.38 KiB) Viewed 4982 times

Time to make custom manifold and exhaust

[crabo249]

The original alternator bracket was cut to size using an angle grinder and used to mount the alternator,all that's needed now is a custom tension bar

alternator

rebuild february 2012 009.JPG (64.44 KiB) Viewed 4980 times

Alternator bracket

rebuild february 2012 010.JPG (62.43 KiB) Viewed 4980 times

As the engine sits a little higher than the old 1800 unit i've put an air scoop in

Hood scoop

Rebuild March 2012 x3 003.JPG (57.16 KiB) Viewed 4980 times

[crabo249]

I havn,t been able to work on the mechanics of the car for various reasons, so i thought i'll have a go at the interior.

Automotive Vynil was bought from ebay and with lots of spray glue and a staple gun off i went

The first job to tackle was the headlining so i used the old boards as templates and added new foam

Headlinging board and foam

Rebuild March 2012 x3 034.JPG (51.11 KiB) Viewed 4979 times

I used ivory headlining material

Ivory headlining

Rebuild March 2012 x3 035.JPG (57.8 KiB) Viewed 4979 times

C post sections

Rebuild March 2012 x4 009.JPG (62.2 KiB) Viewed 4979 times